收藏本站
DATASHEET
5mm Infrared LED
SIR333-A
Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest
possible temperature is desirable for the LEDs.
?
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.
4.
Cleaning
?
?
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED
5.
Heat Management
?
?
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.
6.
ESD (Electrostatic Discharge)
?
?
?
?
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of
friction between LEDs during storage and handing.
7.
Other
?
?
?
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above
specification.
When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t
reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.
8
www.everlight.com
:3
Revision Copyright ?
LifecyclePhase:
No: Release
2010, Everlight All Rights Reserved. Release Date : Mar.29.2013. Issue DIR-0000952 Date:2013-05-30 14:24:46.0
Expired Period: Forever
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SIR383C LED IR 5MM BLUE WATER CLEAR AXL
SIR383 LED IR 5MM BLUE WATER CLEAR AXL
SIR404DP-T1-GE3 MOSFET N-CH D-S 20V 8-SOIC
SIR406DP-T1-GE3 MOSFET N-CH D-S 25V PPAK 8SOIC
SIR414DP-T1-GE3 MOSFET N-CH D-S 40V 8-SOIC
SIR418DP-T1-GE3 MOSFET N-CH D-S 40V PPAK 8SOIC
SIR436DP-T1-GE3 MOSFET N-CH D-S 25V PPAK 8SOIC
SIR440DP-T1-GE3 MOSFET N-CH 20V 60A PPAK 8SOIC
相关代理商/技术参数
SIR333-A_05 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Infrared LED, T-1 3/4
SIR333C 制造商:Everlight Electronics Co 功能描述:LED INFRARED - Bulk
SIR333C/H0/L9 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Infrared LED, T-1 3/4
SIR333C-H0 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5mm Infrared LED, T-1 3/4
SIR-341ST3F 功能描述:红外发射源 IR EMITTER FOR REMOTE CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 波长:880 nm 射束角:+/- 25 辐射强度: 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:Side Looker 封装:Bulk
SIR-341ST3F_10 制造商:ROHM 制造商全称:Rohm 功能描述:Infrared light emitting diode, top view type
SIR-341ST3FF 功能描述:EMITTER IR 940NM RADIAL RoHS:是 类别:光电元件 >> 红外发射极 系列:- 标准包装:1,200 系列:- 电流 - DC 正向(If):100mA 辐射强度(le)最小值@正向电流:27mW/sr @ 100mA 波长:940nm 正向电压:1.6V 视角:40° 方向:顶视图 安装类型:通孔 封装/外壳:径向 包装:带卷 (TR)
SIR-341ST3FM 制造商:ROHM Semiconductor 功能描述: